LIGHTNING CURE EPOXY - A
Version 2.0
SDS Number: 400001000063
Date of last issue: 09/18/2022 Date of first issue: 09/18/2022
SECTION 1. IDENTIFICATION
Product name |
:GENERAL USE RESIN - A |
Manufacturer or supplier's details
Company name of s Address |
upplier : The Epoxy Resin Store
540 CRANE STREET United States of America (USA) |
Telephone
E-mail address of person responsible for the SDS |
: (951) 677-0400
|
Emergency telephone number :(951) 677-0400
Recommended use of the chemical and restrictions on use
Recommended use : Epoxy constituents
SECTION 2. HAZARDS IDENTIFICATION
GHS classification in accordance with 29 CFR 1910.1200
Skin irritation |
Category 2 |
Eye irritation |
Category 2A
Category 1 |
Skin sensitisation |
|
Short-term (acute) aquatic hazard |
|
Chronic aquatic toxicity |
|
GHS label elements
Hazard pictograms |
|
|
Signal word |
|
|
Hazard statements |
: |
H315 Causes skin irritation. H317 May cause an allergic skin reaction. |
Precautionary statements |
: |
Prevention: P261 Avoid breathing dust/ fume/ gas/ mist/ vapours/ spray. |
LIGHTNING CURE EPOXY DATA SHEET - A
Version 2.0
SDS Number:
40000100063
P264 Wash skin thoroughly after handling.
P272 Contaminated work clothing must not be allowed out of the workplace.
P273 Avoid release to the environment.
P280 Wear protective gloves/ eye protection/ face protection.
Response:
P302 + P352 IF ON SKIN: Wash with plenty of soap and water. P305 + P351 + P338 IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing.
P333 + P313 If skin irritation or rash occurs: Get medical advice/ attention.
P337 + P313 If eye irritation persists: Get medical advice/ attention.
P362 Take off contaminated clothing and wash before reuse. P391 Collect spillage.
Storage:
Not available
Disposal:
P501 Dispose of contents/container to an approved facility in accordance with local, regional, national and international regulations.
Other hazards
None known.
SECTION 3. COMPOSITION/INFORMATION ON INGREDIENTS
Substance / Mixture |
: |
Substance |
Hazardous components
Chemical name |
CAS-No. |
Concentration (% w/w) |
|
2,2'-[(1-methylethylidene)bis(4,1- phenyleneoxymethylene)]bisoxirane |
1675-54-3 |
90 |
- 100 |
The specific chemical identity and/or exact percentage (concentration) of composition may be withheld as a trade secret.
Both 25068-38-6 and 1675-54-3 can be used to describe the epoxy resin which is produced through the reaction of Bisphenol A and Epichlorhydrin
SECTION 4. FIRST AID MEASURES
General advice |
: |
Move out of dangerous area. Show this safety data sheet to the doctor in attendance. Treat symptomatically. Get medical attention if symptoms occur. |
If inhaled |
: |
If inhaled, remove to fresh air. Get medical attention if symptoms occur. |
In case of skin contact |
: |
If skin irritation persists, call a physician. If on skin, rinse well with water. |
Version 2.0
SDS Number:
400001000063
|
|
If on clothes, remove clothes. |
In case of eye contact |
: |
Immediately flush eye(s) with plenty of water. Remove contact lenses. Keep eye wide open while rinsing. If eye irritation persists, consult a specialist. |
If swallowed |
: |
Keep respiratory tract clear. Never give anything by mouth to an unconscious person. If symptoms persist, call a physician. |
Most important symptoms and effects, both acute and delayed |
: |
None known. |
Notes to physician |
: |
Treat symptomatically. |
SECTION 5. FIREFIGHTING MEASURES
Suitable extinguishing media |
: |
Use extinguishing measures that are appropriate to local circumstances and the surrounding environment. |
Unsuitable extinguishing media |
: |
High volume water jet |
Specific hazards during firefighting |
: |
Do not allow run-off from fire fighting to enter drains or water courses. |
Hazardous combustion products |
: |
No hazardous combustion products are known |
|
|
Carbon oxides Halogenated compounds |
Specific extinguishing methods |
: |
No data is available on the product itself. |
Further information |
: |
Collect contaminated fire extinguishing water separately. This must not be discharged into drains. Fire residues and contaminated fire extinguishing water must be disposed of in accordance with local regulations. |
Special protective equipment for firefighters |
: |
Wear self-contained breathing apparatus for firefighting if necessary. |
SECTION 6. ACCIDENTAL RELEASE MEASURES
Personal precautions, protective equipment and emergency procedures |
: |
Use personal protective equipment. Refer to protective measures listed in sections 7 and 8. |
Environmental precautions |
: |
Prevent product from entering drains. |
Version 2.0
SDS Number:
400001000063
Prevent further leakage or spillage if safe to do so.
If the product contaminates rivers and lakes or drains inform respective authorities.
Methods and materials for containment and cleaning up |
: |
Soak up with inert absorbent material (e.g. sand, silica gel, acid binder, universal binder, sawdust). Keep in suitable, closed containers for disposal. |
SECTION 7. HANDLING AND STORAGE
Advice on protection against fire and explosion |
: |
Normal measures for preventive fire protection. |
Advice on safe handling |
: |
Do not breathe vapours/dust. Avoid exposure - obtain special instructions before use. Avoid contact with skin and eyes. For personal protection see section 8. Smoking, eating and drinking should be prohibited in the application area. Dispose of rinse water in accordance with local and national regulations. Persons susceptible to skin sensitisation problems or asthma, allergies, chronic or recurrent respiratory disease should not be employed in any process in which this mixture is being used. |
Conditions for safe storage |
: |
Keep container tightly closed in a dry and well-ventilated place. Containers which are opened must be carefully resealed and kept upright to prevent leakage. Keep in properly labelled containers. |
Materials to avoid |
: |
Strong acids Strong bases Strong oxidizing agents |
Recommended storage temperature |
: |
36 - 104 °F / 2 - 40 °C |
Further information on storage stability |
: |
No decomposition if stored and applied as directed. |
SECTION 8. EXPOSURE CONTROLS/PERSONAL PROTECTION
Components with workplace control parameters
Contains no substances with occupational exposure limit values.
Personal protective equipment
Respiratory protection |
: |
General and local exhaust ventilation is recommended to maintain vapor exposures below recommended limits. Where concentrations are above recommended limits or are unknown, appropriate respiratory protection should be worn. Follow OSHA respirator regulations (29 CFR 1910.134) and use NIOSH/MSHA approved respirators. Protection provided by air purifying respirators against exposure to any hazardous chemical is limited. Use a positive pressure air |
Version 2.0
SDS Number:
400001000063
supplied respirator if there is any potential for uncontrolled release, exposure levels are unknown, or any other circumstance where air purifying respirators may not provide adequate protection.
Hand protection
Material |
: |
butyl-rubber |
Break through time |
: |
> 8 h |
Material |
: |
Ethyl Vinyl Alcohol Laminate (EVAL) |
Break through time |
: |
> 8 h |
Material |
: |
Nitrile rubber |
Break through time |
: |
10 - 480 min |
Material |
: |
Neoprene |
Break through time |
: |
10 - 480 min |
Remarks |
: |
The suitability for a specific workplace should be discussed with the producers of the protective gloves. Take note of the information given by the producer concerning permeability and break through times, and of special workplace conditions (mechanical strain, duration of contact). |
Eye protection |
: |
Eye wash bottle with pure water Tightly fitting safety goggles Wear face-shield and protective suit for abnormal processing problems. |
Skin and body protection |
: |
Impervious clothing Choose body protection according to the amount and concentration of the dangerous substance at the work place. |
Hygiene measures |
: |
When using do not eat or drink. When using do not smoke. Wash hands before breaks and at the end of workday. |
SECTION 9. PHYSICAL AND CHEMICAL PROPERTIES
Appearance |
: |
liquid |
Colour |
: |
colourless |
Odour |
: |
slight |
Odour Threshold |
: |
No data is available on the product itself. |
pH |
: |
ca. 7 (68 °F / 20 °C) Concentration: 500 g/l |
Freezing point |
: |
No data is available on the product itself. |
Melting point |
: |
No data is available on the product itself. |
Version 2.0
SDS Number:
400001000063
Boiling point |
: |
> 392 °F / > 200 °C |
Flash point |
: |
> 392 °F / > 200 °C Method: Pensky-Martens closed cup |
Evaporation rate |
: |
No data is available on the product itself. |
Flammability (solid, gas) |
: |
No data is available on the product itself. |
Flammability (liquids) |
: |
No data is available on the product itself. |
Upper explosion limit / Upper flammability limit |
: |
No data is available on the product itself. |
Lower explosion limit / Lower flammability limit |
: |
No data is available on the product itself. |
Vapour pressure |
: |
< 0.0001 hPa (77 °F / 25 °C) |
Relative vapour density |
: |
No data is available on the product itself. |
Relative density |
: |
1.15 - 1.17 (77 °F / 25 °C) |
Density |
: |
1.17 - 1.2 g/cm3 (77 °F / 25 °C) |
Solubility(ies)
Water solubility |
: |
practically insoluble (68 °F / 20 °C) |
Solubility in other solvents |
: |
No data is available on the product itself. |
Partition coefficient: n- octanol/water |
: |
log Pow: 3.8 (77 °F / 25 °C) |
Auto-ignition temperature |
: |
does not ignite |
Decomposition temperature |
: |
> 392 °F / > 200 °C |
Self-Accelerating decomposition temper (SADT)
Viscosity Viscosity, dynamic Explosive properties Oxidizing properties Particle size |
: No data is available on the product itself. ature
: 600 - 1000 mPa.s (77 °F / 25 °C)
: No data is available on the product itself.
: No data is available on the product itself.
: No data is available on the product itself. |
SECTION 10. STABILITY AND REACTIVITY
Version 2.0
SDS Number:
400001000063
Reactivity |
: |
No dangerous reaction known under conditions of normal use. |
Chemical stability |
: |
Stable under normal conditions. |
Possibility of hazardous reactions |
: |
No hazards to be specially mentioned. |
Conditions to avoid |
: |
None known. |
Incompatible materials |
: |
Strong acids Strong bases Strong oxidizing agents |
Hazardous decomposition products |
: |
carbon dioxide carbon monoxide Halogenated compounds |
SECTION 11. TOXICOLOGICAL INFORMATION
Information on likely routes of exposure |
: |
No data is available on the product itself. |
Acute toxicity
Components:
2,2'-[(1-methylethylidene)bis(4,1-phenyleneoxymethylene)]bisoxirane:
Acute oral toxicityComponents |
: |
LD50 (Rat, female): > 2,000 mg/kg Method: OECD Test Guideline 420 Assessment: The substance or mixture has no acute oral toxicity |
Acute inhalation toxicity |
: |
No data available |
Components:
2,2'-[(1-methylethylidene)bis(4,1-phenyleneoxymethylene)]bisoxirane:
Acute dermal toxicity |
: |
LD50 (Rat, male and female): > 2,000 mg/kg Method: OECD Test Guideline 402 Assessment: The substance or mixture has no acute dermal toxicity |
Acute toxicity (other routes of administration) |
: |
No data available |
Skin corrosion/irritation
Components:
2,2'-[(1-methylethylidene)bis(4,1-phenyleneoxymethylene)]bisoxirane: Species: Rabbit
Assessment: Mild skin irritant Method: OECD Test Guideline 404 Result: Irritating to skin.
Version 2.0
SDS Number:
400001000063
Serious eye damage/eye irritation
Components:
2,2'-[(1-methylethylidene)bis(4,1-phenyleneoxymethylene)]bisoxirane: Species: Rabbit
Result: Irritating to eyes. Assessment: Mild eye irritant Method: OECD Test Guideline 405
Respiratory or skin sensitisation
Components:
2,2'-[(1-methylethylidene)bis(4,1-phenyleneoxymethylene)]bisoxirane: Exposure routes: Skin
Species: Mouse
Assessment: May cause sensitisation by skin contact. Method: OECD Test Guideline 429
Result: Causes sensitisation.
Assessment: |
No data available |
Germ cell mutagenicity
Components:
2,2'-[(1-methylethylidene)bis(4,1-phenyleneoxymethylene)]bisoxirane:
Genotoxicity in vitro |
: |
Metabolic activation: with and without metabolic activation Method: OECD Test Guideline 476 Result: positive |
|
|
Concentration: 0 - 5000 ug/plate Metabolic activation: with and without metabolic activation Method: OECD Test Guideline 471 Result: positive |
Components:
2,2'-[(1-methylethylidene)bis(4,1-phenyleneoxymethylene)]bisoxirane:
Genotoxicity in vivo |
: |
Cell type: Germ Application Route: Oral Method: OECD Test Guideline 478 Result: negative |
|
|
Cell type: Somatic Application Route: Oral Dose: 0 - 5000 mg/kg Method: OPPTS 870.5395 Result: negative |
Carcinogenicity
Components:
2,2'-[(1-methylethylidene)bis(4,1-phenyleneoxymethylene)]bisoxirane: Species: Rat, male and female
Application Route: Oral Exposure time: 24 month(s) Dose: 15 mg/kg
Frequency of Treatment: 7 days/week Method: OECD Test Guideline 453 Result: negative |
Species: Mouse, male Application Route: Dermal Exposure time: 24 month(s) Dose: 0.1 mg/kg Frequency of Treatment: 3 days/week Method: OECD Test Guideline 453 Result: negative |
Species: Rat, female Application Route: Dermal Exposure time: 24 month(s) Dose: 1 mg/kg Frequency of Treatment: 5 days/week Method: OECD Test Guideline 453 Result: negative |
Carcinogenicity - Assessment |
: |
No data available |
IARC |
No component of this product present at levels greater than or equal to 0.1% is identified as probable, possible or confirmed human carcinogen by IARC. |
ACGIH |
No component of this product present at levels greater than or equal to 0.1% is identified as a carcinogen or potential carcinogen by ACGIH. |
OSHA |
No component of this product present at levels greater than or equal to 0.1% is on OSHA’s list of regulated carcinogens. |
NTP |
No component of this product present at levels greater than or equal to 0.1% is identified as a known or anticipated carcinogen by NTP. |
Reproductive toxicity
Components:
2,2'-[(1-methylethylidene)bis(4,1-phenyleneoxymethylene)]bisoxirane:
Effects on fertility |
: |
Test Type: Two-generation study Species: Rat, male and female Application Route: Oral Dose: >750 milligram per kilogram General Toxicity - Parent: No-observed-effect level: 540 mg/kg body weight General Toxicity F1: No-observed-effect level: 540 mg/kg body weight Symptoms: No adverse effects Method: OECD Test Guideline 416 Result: No effects on fertility and early embryonic development were detected. |
Components:
2,2'-[(1-methylethylidene)bis(4,1-phenyleneoxymethylene)]bisoxirane:
Effects on foetal development |
: |
Species: Rabbit, female Application Route: Dermal General Toxicity Maternal: No observed adverse effect level: 30 mg/kg body weight Method: Other guidelines Result: No teratogenic effects
Species: Rabbit, female Application Route: Oral General Toxicity Maternal: No observed adverse effect level: 60 mg/kg body weight Method: OECD Test Guideline 414 Result: No teratogenic effects
Species: Rat, female Application Route: Oral General Toxicity Maternal: No observed adverse effect level: 180 mg/kg body weight Method: OECD Test Guideline 414 Result: No teratogenic effects |
Reproductive toxicity - Assessment |
: |
No data available |
STOT - single exposure
No data available
STOT - repeated exposure
No data available
Repeated dose toxicity
Components:
2,2'-[(1-methylethylidene)bis(4,1-phenyleneoxymethylene)]bisoxirane:
Species: Rat, male and female NOAEL: 50 mg/kg Application Route: Ingestion Exposure time: 14 Weeks Number of exposures: 7 d Method: Subchronic toxicity |
Species: Rat, male and female NOEL: 10 mg/kg Application Route: Skin contact Exposure time: 13 Weeks Number of exposures: 5 d Method: Subchronic toxicity |
Species: Mouse, male NOAEL: 100 mg/kg Application Route: Skin contact Exposure time: 13 Weeks |
LIGHTNING CURE EPOXY DATA SHEET - A
Version 2.0
SDS Number:
400001000063
Number of exposures: 3 d Method: Subchronic toxicity
Repeated dose toxicity - Assessment |
: |
No data available |
Aspiration toxicity
No data available
Experience with human exposure
General Information: |
No data available |
Inhalation: |
No data available |
Skin contact: |
No data available |
Eye contact: |
No data available |
Ingestion: |
No data available |
Toxicology, Metabolism, Distribution
No data available
Neurological effects
No data available
Further information
Ingestion: |
No data available |
SECTION 12. ECOLOGICAL INFORMATION
Ecotoxicity
Components:
2,2'-[(1-methylethylidene)bis(4,1-phenyleneoxymethylene)]bisoxirane:
Toxicity to fish |
: |
LC50 (Oncorhynchus mykiss (rainbow trout)): 1.5 mg/l Exposure time: 96 h Test Type: static test Test substance: Fresh water Method: OECD Test Guideline 203 |
Components:
2,2'-[(1-methylethylidene)bis(4,1-phenyleneoxymethylene)]bisoxirane:
Toxicity to daphnia and other aquatic invertebrates |
: |
EC50 (Daphnia magna (Water flea)): 2.7 mg/l Exposure time: 48 h Test Type: static test Test substance: Fresh water |
Components:
2,2'-[(1-methylethylidene)bis(4,1-phenyleneoxymethylene)]bisoxirane:
Toxicity to algae |
: |
EC50 (Selenastrum capricornutum (green algae)): 9.4 mg/l Exposure time: 72 h Test Type: static test Test substance: Fresh water Method: EPA-660/3-75-009 |
M-Factor (Acute aquatic toxicity) |
: |
No data available |
Toxicity to fish (Chronic toxicity) |
: |
No data available |
Components:
2,2'-[(1-methylethylidene)bis(4,1-phenyleneoxymethylene)]bisoxirane:
Toxicity to daphnia and other aquatic invertebrates (Chronic toxicity) |
: |
NOEC (Daphnia magna (Water flea)): 0.3 mg/l Exposure time: 21 d Test Type: semi-static test Test substance: Fresh water Method: OECD Test Guideline 211 |
M-Factor (Chronic aquatic toxicity) |
: |
No data available |
Components:
2,2'-[(1-methylethylidene)bis(4,1-phenyleneoxymethylene)]bisoxirane:
Toxicity to microorganisms |
: |
IC50 (activated sludge): > 100 mg/l Exposure time: 3 h Test Type: static test Test substance: Fresh water |
Toxicity to soil dwelling organisms |
: |
No data available |
Plant toxicity |
: |
No data available |
Sediment toxicity |
: |
No data available |
Toxicity to terrestrial organisms |
: |
No data available |
Ecotoxicology Assessment
Acute aquatic toxicity |
: |
No data available |
Chronic aquatic toxicity |
: |
No data available |
Toxicity Data on Soil |
: |
No data available |
Other organisms relevant to the environment |
: |
No data available |
Persistence and degradability
Components:
2,2'-[(1-methylethylidene)bis(4,1-phenyleneoxymethylene)]bisoxirane:
Biodegradability |
: |
Inoculum: Sewage (STP effluent) Concentration: 20 mg/l Result: Not readily biodegradable. Biodegradation: 5 % Exposure time: 28 d Method: OECD Test Guideline 301F |
Biochemical Oxygen Demand (BOD) |
: |
No data available |
Chemical Oxygen Demand (COD) |
: |
No data available |
BOD/COD |
: |
No data available |
ThOD |
: |
No data available |
BOD/ThOD |
: |
No data available |
Dissolved organic carbon (DOC) |
: |
No data available |
Physico-chemical removability |
: |
No data available |
Components:
2,2'-[(1-methylethylidene)bis(4,1-phenyleneoxymethylene)]bisoxirane:
Stability in water |
: |
Degradation half life(DT50): 4.83 d (77 °F / 25 °C) pH: 4 Method: OECD Test Guideline 111 Remarks: Fresh water |
|
|
Degradation half life(DT50): 7.1 d (77 °F / 25 °C) pH: 9 Method: OECD Test Guideline 111 Remarks: Fresh water |
|
|
Degradation half life(DT50): 3.58 d (77 °F / 25 °C) pH: 7 Method: OECD Test Guideline 111 Remarks: Fresh water |
Photodegradation |
: |
No data available |
Impact on Sewage Treatment |
: |
No data available |
Bioaccumulative potential
Components:
Version 2.0
SDS Number:
400001000063
2,2'-[(1-methylethylidene)bis(4,1-phenyleneoxymethylene)]bisoxirane:
Bioaccumulation |
: |
Bioconcentration factor (BCF): 31 Remarks: Does not bioaccumulate. |
Partition coefficient: n- octanol/water - Product |
: |
log Pow: 3.8 (77 °F / 25 °C) |
Mobility in soil
Mobility |
: |
No data available |
Components:
2,2'-[(1-methylethylidene)bis(4,1-phenyleneoxymethylene)]bisoxirane:
Distribution among environmental compartments |
: |
Koc: 445 |
Stability in soil |
: |
No data available |
Other adverse effects
Environmental fate and pathways |
: |
No data available |
Results of PBT and vPvB assessment |
: |
No data available |
Endocrine disrupting potential |
: |
No data available |
Adsorbed organic bound halogens (AOX) |
: |
No data available |
Hazardous to the ozone layer
Ozone-Depletion Potential |
: |
Regulation: 40 CFR Protection of Environment; Part 82 Protection of Stratospheric Ozone - CAA Section 602 Class I Substances Remarks: This product neither contains, nor was manufactured with a Class I or Class II ODS as defined by the U.S. Clean Air Act Section 602 (40 CFR 82, Subpt. A, App.A + B). |
Additional ecological information - Product |
: |
An environmental hazard cannot be excluded in the event of |
|
unprofessional handling or disposal.
An environmental hazard cannot be excluded in the event of unprofessional handling or disposal. |
Global warming potential (GWP) |
: |
No data available |
SECTION 13. DISPOSAL CONSIDERATIONS
Disposal methods
Version 2.0
SDS Number:
400001000063
Waste from residues |
: |
The product should not be allowed to enter drains, water courses or the soil. Do not contaminate ponds, waterways or ditches with chemical or used container. Send to a licensed waste management company. Dispose of as hazardous waste in compliance with local and national regulations. Dispose of contents/ container to an approved waste disposal plant. |
Contaminated packaging |
: |
Empty remaining contents. Dispose of as unused product. Do not re-use empty containers. |
SECTION 14. TRANSPORT INFORMATION
International Regulations
IATA |
UN/ID No. |
Proper shipping name |
: NOT REGULATED UNDER 110 GALLONS
: (BISPHENOL A EPOXY RESIN)
Packing instruction (passenger aircraft)
: NR
Class |
Packing group |
Labels |
Packing instruction (cargo aircraft) |
: NR
: Not regulated
: NR
: NR
IMDG |
|
UN number Proper shipping name |
: Not Regulated : (BISPHENOL A EPOXY RESIN) |
(BISPHENOL A EPOXY RESIN)
Class |
Packing group |
Labels |
EmS Code |
: NR
: NR
: NR
: N/A
Marine pollutant
Transport in bulk according to Annex II of MARPOL 73/78 and the IBC Code
Not applicable for product as supplied.
National Regulations
DOT Classification |
|
UN/ID/NA number Proper shipping name |
: NOT REGULATE DUNDER 110 GALLONS : (BISPHENOL A EPOXY RESIN) |
Version 2.0
SDS Number:
400001000063
Class Packing group Labels ERG Code Marine pollutant |
(BISPHENOL A EPOXY RESIN) : NOT REGULATED
NOT REGULTAED NA NA |
Special precautions for user
The transport classification(s) provided herein are for informational purposes only, and solely based upon the properties of the unpackaged material as it is described within this Safety Data Sheet. Transportation classifications may vary by mode of transportation, package sizes, and variations in regional or country regulations.
SECTION 15. REGULATORY INFORMATION
Components |
CAS-No. |
Component RQ (lbs) |
Calculated product RQ (lbs) |
1-chloro-2,3-epoxypropane |
106-89-8 |
100 |
* |
EPCRA - Emergency Planning and Community Right-to-Know Act CERCLA Reportable Quantity
*: Calculated RQ exceeds reasonably attainable upper limit.
SARA 311/312 Hazards |
: |
Skin corrosion or irritation Serious eye damage or eye irritation Respiratory or skin sensitisation |
SARA 313 |
: |
This material does not contain any chemical components with known CAS numbers that exceed the threshold (De Minimis) reporting levels established by SARA Title III, Section 313. |
This product does not contain any hazardous air pollutants (HAP), as defined by the U.S. Clean Air Act Section 112 (40 CFR 61).
California Prop. 65
WARNING: This product can expose you to chemicals including 1-chloro-2,3-epoxypropane, which is/are known to the State of California to cause cancer, and 1-chloro-2,3-epoxypropane,
4,4'-isopropylidenediphenol, which is/are known to the State of California to cause birth defects or other reproductive harm. For more information go to www.P65Warnings.ca.gov.
4,4'-isopropylidenediphenol, which is/are known to the State of California to cause birth defects or other reproductive harm. For more information go to www.P65Warnings.ca.gov.
The components of this product are reported in the following inventories:
CH INV |
: |
On the inventory, or in compliance with the inventory |
DSL |
: |
All components of this product are on the Canadian DSL |
AICS |
: |
On the inventory, or in compliance with the inventory |
NZIoC |
: |
On the inventory, or in compliance with the inventory |
ENCS |
: |
On the inventory, or in compliance with the inventory |
KECI |
: |
On the inventory, or in compliance with the inventory |
PICCS |
: |
On the inventory, or in compliance with the inventory |
IECSC |
: |
On the inventory, or in compliance with the inventory |
TCSI |
: |
On the inventory, or in compliance with the inventory |
TSCA |
: |
On the inventory, or in compliance with the inventory |
Version 2.0
SDS Number:
400001000063
Inventories
AICS (Australia), DSL (Canada), IECSC (China), REACH (European Union), ENCS (Japan), ISHL (Japan), KECI (Korea), NZIoC (New Zealand), PICCS (Philippines), TCSI (Taiwan), TSCA (USA)
TSCA - 5(a) Significant New Use Rule List of Chemicals
No substances are subject to a Significant New Use Rule.
US. Toxic Substances Control Act (TSCA) Section 12(b) Export Notification (40 CFR 707, Subpt D)
No substances are subject to TSCA 12(b) export notification requirements.
SECTION 16. OTHER INFORMATION
Further information
NFPA 704: HMIS® IV:
0
1
0
HEALTH FLAMMABILITY
PHYSICAL HAZARD
1
0
0
Instability
Health
Flammability
Special hazard.
HMIS® ratings are based on a 0-4 rating scale, with 0 representing minimal hazards or risks, and 4 representing significant hazards or risks. The "*" represents a chronic hazard, while the "/" represents the absence of a chronic hazard.
Disclaimer: This information and any recommendations, technical or otherwise, are presented in good faith and believed to be correct as of the date prepared. Recipients of this information and recommendations must make their own determination as to its suitability for their purposes. In no event shall THE EPOXY RESIN STORE assume liability for damages or losses of any kind or nature that result from the use of or reliance upon this information and recommendations. THE EPOXY RESIN STORE EXPRESSLY DISCLAIMS ANY REPRESENTATIONS AND WARRANTIES OF ANY KIND, WHETHER EXPRESS OR IMPLIED, AS TO THE ACCURACY, COMPLETENESS, NON-INFRINGEMENT, MERCHANTABILITY AND/OR FITNESS FOR A PARTICULAR PURPOSE (EVEN IF THE EPOXY RESIN STORE IS AWARE OF SUCH PURPOSE) WITH RESPECT TO ANY
INFORMATION AND RECOMMENDATIONS PROVIDED. Reference to any trade names used by other companies is neither a recommendation nor an endorsement of the corresponding product, and does not imply that similar products could not be used. THE EPOXY RESIN STORE reserves the right
to make any changes to the information and/or recommendations at any time,without prior or subsequent notice.