MIXING INSTRUCTIONS - Clearcast 7000

CLEARCAST 7000

Here is a link to download. 

BUY CLEARCAST 7000 Here: https://www.theepoxyresinstore.com/collections/craft-and-jewelry-epoxy-resin/products/clearcast-7000-jewelry-crafting-casting-epoxy-resin-mixing

View a short demo of the mixing instructions here: 

MIXING INSTRUCTIONS

WARNING TO ALL EPOXY RESIN USERS. EPOXY RESIN MIXTURES GENERATES HEAT: PLEASE READ (2 MINUTES TO SAVE DAYS). 
DO NOT MIX EVERYTHING AT ONCE!
When mixing epoxy resin, a chemical reaction occurs. This exothermic reaction creates heat. The more you mix together the more chemical reaction occurs (more heat). Be sure you are ready to pour out the mixture prior to actually mixing. Do not leave a large volume of freshly mixed epoxy resin inside a bucket unattended for more than 3-5 minutes. 

These mixing instructions are only recommendations. Please understand that larger mixes will cure faster and smaller mixes will cure slower. If your mixes are running hot, apply to your application quicker and/or mix smaller batches. (Weather alert! The heat will accelerate the cure and cold weather will slow cure).

  • 1.        Clearcast 7000 is mixed at a 1:1 ratio by volume. If mixing by weight, mix 100/85 p.b.w. (resin/hardener). It is recommended to mix a minimum of at least 50 grams ( 2-3oz.). This weight mixture will help             in avoiding curing problems. Small batches below 50 grams (2-3oz.) may experience improper curing.
  • 2.        When mixing your resin, make sure to use a round container.
  • 3.        When mixing, always pour the resin into hardener. Hand stir components for a minimum of 3-5 minutes in a round fashion. Stir slowly to help avoid bubbles. Make sure to scrape the sides and the                       bottom of the mixing container. It is very important that the 2 components are properly mixed.
  • 4.        Pour mixed components into another empty cup. Again, hand stir mixed resin for 3-5 minutes.
  • 5.        Let mixed components stand in mixing cup for 3-5 minutes. This will allow for any bubbles to rise to the surface. A torch or alcohol spray can be used to alleviate bubbles at this time.
  • 6.        When pouring your resin into your application, try and pour as close to your piece as possible. Pour from left to right (or vice versa) so that resin flows from the front of your piece to the back. These                     techniques help avoid bubble entrapment.

Please Note: Cure times will vary depending on mass and temperature. The heat will accelerate curing whereas cold will decrease curing cycles. Large castings will cure very quickly whereas small castings may take longer than normal to fully cure.

Full cure at the thin-film set is roughly 16-24 hours based on room temperature of 77F. For small castings and thin coats, full cure is typically 24 hours. Any sanding or polishing of a cured piece should be done after a full cure (24 hours).

https://help.theepoxyresinstore.com/

PS: Would you like to contribute to our faq or community? Make a video documenting your project creation or educational piece, we would love to share with our community. 

As a small business, we really appreciate your purchase, reviews, and referrals. 

support@theepoxyresinstore.com 

https://www.theepoxyresinstore.com

The Epoxy Resin Store
Address: 540 Crane Street Unit A Lake Elsinore, CA 92530 
Phone: (951) 677-0400
Email: support@theepoxyresinstore.com
Hours of Customer Service: 8:30 AM - 4:30 PM (PST) Mon - Fri 
Closed: Sat - Sun 
We respond within 1 business day

Did this answer your question? Thanks for the feedback There was a problem submitting your feedback. Please try again later.

Still need help? Contact Us Contact Us